Sourcing & Buying Guide

Commercial Dishwasher Electrical Requirements: Phase, Voltage and Booster Load

Will your replacement dishwasher use the existing supply? Start with the exact model’s electrical schedule. Two machines can fit the same wash station and take the same racks while requiring different voltages, different phases or a separate feed for the rinse booster.

Match voltage, frequency, phase and the number of supply points before ordering. Ask for the rated load and the manufacturer’s connection data for each point. Confirm that the quoted setup will also handle your busiest hour at the inlet water temperature available on site.

Does a commercial dishwasher need three-phase power?

It depends on the selected configuration. The UK technical sheet for one MEIKO M-iClean UM+ undercounter build lists 230 V, 50 Hz, single-phase and a connected load of 4.9 kW. Hobart’s AM16 instructions also list a single-phase, single-point variant with a specified booster alongside several three-phase variants. Check the exact model suffix, heater option and local-market sheet. A nominal voltage that looks familiar is only one part of the match.

What to put on the dishwasher line of your equipment schedule
CheckWhat to recordWhy it matters
SupplyVoltage or allowed range, Hz, phase and any neutral requirement stated by the manufacturer.The same cabinet or model family can have several electrical builds.
Feed countOne combined supply, or separate entries for the machine and booster. List any separately powered accessories.The equipment schedule must show each required supply point, even if the booster is inside the cabinet.
Load per feedRated current, connected kW where stated, and the manufacturer’s circuit and protection data.Rated running current and the values used to design the supply are different fields.
Water and outputInlet temperature and pressure conditions, programme used and racks per hour at those conditions.A machine that fits the available supply still has to keep up with the racks arriving at peak service.

Does the booster heater need its own supply?

A rinse booster raises the incoming water temperature for the final rinse. For purchasing, the decisive detail is how the specific model and heater option are documented for supply. Use the combined rating when the manufacturer specifies one connection. Use two schedule lines when it specifies separate connections. List a remote booster as its own item and ask which figures already include it.

  1. Combined feed One supply point → dishwasher and booster. Record the combined rating once.
  2. Separate feeds Supply A → machine. Supply B → booster or booster and controls. Record both rows.
  3. Building hot water Identify the hot water source and confirm the delivered temperature during peak washing.
Three checks for your equipment schedule. The hot water check can apply to either connection arrangement.

Worked example: reading one manufacturer’s schedule. The Hobart AM16-BAS sheet lists a 208–240 V, 60 Hz, three-phase single-point option at 52.5 A rated current. Its documented dual-point version at that supply lists the machine at 26.9 A and the booster and controls at 25.6 A. Record either one combined entry or the two separate entries that describe the selected build. The figures reconcile in this example; the two separate feeds remain distinct. Copy the manufacturer’s separate circuit and protection fields as stated and pass the schedule to your electrical designer.

Check how water temperature affects peak output

Compare racks per hour using the exact programme, required rinse conditions and water supply specified for the quote. Ask for sustained throughput when the dishwasher, pre-rinse sink and other outlets are drawing from the same hot water system. If the available inlet water is cooler, request the model’s expected recovery time and output under that condition. The incoming temperature matters even when the site’s electrical figures match.

Illustration: If each rack uses 2 L of fresh rinse water (about 2 kg) and that water needs a 35 °C temperature rise, the useful heat added is about 0.081 kWh per rack: 2 kg × 4.19 kJ/(kg·°C) × 35 °C ÷ 3,600 kJ/kWh. At 40 racks per hour, that is about 3.3 kW of average heat delivered to the rinse water, before heat loss. This calculation uses assumed values; the manufacturer’s full connected load also depends on the wash tank, pumps, controls and heating arrangement. Read the nameplate and model sheet to establish the electrical requirement.

If the order includes a heat recovery option, ask for a separate comparison at your inlet condition. See our commercial dishwasher heat recovery guide for the water and steam questions to ask.

What to confirm before the purchase order

  1. Send the site supply details. Ask your project electrician for documented voltage, frequency, available phases and available feeds at the proposed location.
  2. Send the operating brief. Share peak racks per hour, the largest tray or rack and inlet water temperature during peak service. Confirm rack and wash chamber dimensions separately.
  3. Review the utility sheet for the quoted build. Match the model suffix, heating option, supply point count, exact connection data and inlet conditions. Update the equipment schedule when any accessory or heater option changes.
  4. Coordinate installation before equipment release. Have the project team confirm the final electrical design, water services and access to service connections.

Plan the dishwashing station with GRACE

Share your rack sizes, peak demand, water supply and available electrical service. GRACE can help compare equipment configurations and coordinate their placement with the washroom layout. Talk to GRACE about a commercial dishwashing station.

Technical references